-
1 растягивающая нагрузка
1) Geology: extension strain2) Aviation: tension load3) Engineering: tensile load, tensile strength, tensile stress, tension weight (от собственной массы)4) Automobile industry: stretching strain5) Oil: tensile loading6) Special term: tearing strain7) Drilling: axial load, tension failure load8) Sakhalin energy glossary: tensile force9) Makarov: traction load10) Caspian: tensile yield loadУниверсальный русско-английский словарь > растягивающая нагрузка
-
2 предел текучести при растяжении
Русско-английский научный словарь > предел текучести при растяжении
-
3 предел текучести при растяжении
Русско-английский новый политехнический словарь > предел текучести при растяжении
-
4 предел упругости при растяжении
Русско-английский научный словарь > предел упругости при растяжении
-
5 предел текучести
1. yield strength[lang name="Russian"]нагрузка, соответствующая началу текучести — yield load
2. yield point; yield limit; yield strength[lang name="Russian"]температура застывания; точка текучести — pour point
[lang name="Russian"]напряжение, возникающее при текучести — yield stress
См. также в других словарях:
Yield (engineering) — The yield strength or yield point of a material is defined in engineering and materials science as the stress at which a material begins to deform plastically. Prior to the yield point the material will deform elastically and will return to its… … Wikipedia
Tensile strength — sigma {UTS}, or S U is the stress at which a material breaks or permanently deforms. Tensile strength is an intensive property and, consequently, does not depend on the size of the test specimen. However, it is dependent on the preparation of the … Wikipedia
yield point — /ˈjild pɔɪnt/ (say yeeld poynt) noun the stress at which an elongation of the test piece of metal in a tensile test first occurs without increase of load. Also, yield stress …
yield point — can be defined as the point where a tensile test piece begins to extend permanently. If the load is reduced to zero, the test piece will not return to its original length … Mechanics glossary
ultimate load — In stress analysis, the minimum load that in its last increment causes a physical breakdown in an aircraft or component during a strength test or a load that, according to computation, should cause such a breakdown. Normally, the ultimate load is … Aviation dictionary
Ceramic matrix composite — Fracture surface of a fiber reinforced ceramic composed of SiC fibers and SiC matrix. The fiber pull out mechanism shown is the key to CMC properties … Wikipedia
Screw — This article is about the fastener. For other uses, see Screw (disambiguation). Screws come in a variety of shapes and sizes for different purposes. U.S. quarter coin (diameter 24 mm) shown for scale. A screw, or bolt, is a type of fastener… … Wikipedia
Nut (hardware) — A nut threaded onto a bolt A nut is a type of hardware fastener with a threaded hole. Nuts are almost always used opposite a mating bolt to fasten a stack of parts together. The two partners are kept together by a combination of their threads… … Wikipedia
Strength of materials — Internal force lines are denser near the hole, a common stress concentration In materials science, the strength of a material is its ability to withstand an applied stress without failure. The applied stress may be tensile, compressive, or shear … Wikipedia
solids, mechanics of — ▪ physics Introduction science concerned with the stressing (stress), deformation (deformation and flow), and failure of solid materials and structures. What, then, is a solid? Any material, fluid or solid, can support normal forces.… … Universalium
Cold formed steel — (CFS) is the common term for products made by rolling or pressing thin gauges of sheet steel into goods. Cold formed steel goods are created by the working of sheet steel using stamping, rolling, or presses to deform the sheet into a usable… … Wikipedia